Application of adhesively bonded single lap joints for fracture assessment of adhesive materials

In this study, a method has been proposed to obtain the failure envelope of brittle adhesives using the experimental failure loads of precracked single lap joints (SLJs). The proposed technique is based on the principles of linear elastic fracture mechanics (LEFM), on J-integral relations, and on results of a numerical analysis. Compared to the previous approaches, the introduced experimental method has some advantages such as low manufacturing costs and simpler test procedure. The proposed method can also provide a wide range of mode mix ratios without the need of an additional apparatus. The fracture envelope obtained from the proposed method was then verified by performing some fracture tests including double cantilever beam (DCB), end-notched flexure (ENF), and single leg bending (SLB) specimens. Good correlation was seen between the fracture envelopes of the proposed method and the ones obtained from the fracture mechanics experiments.     

Curing kinetics and mechanical properties of fast curing epoxy resins with isophorone diamine and N-(3-aminopropyl)-imidazole

Fast curing epoxy resins were prepared by the reactions of diglycidyl ether of bisphenol A with isophorone diamine (IPD) and N-(3-aminopropyl)-imidazole (API), and their curing kinetics and mechanical properties influenced by IPD content were also investigated. The analysis of curing kinetics was based on the nonisothermal differential scanning calorimetry (DSC) data with the typical Kissinger, Ozawa, and Flynn–Wall–Ozawa models, respectively. The glass-transition temperature was also measured by the same technique. Additionally, the mechanical properties including flexural, impact, and tensile performances were tested, and the curing time was estimated by isothermal DSC. The degree of cure (α) dependency of activation energy (E_a ) revealed the complexity of curing reaction. Detailed analysis of the curing kinetics at the molecular level indicated that the dependence of E_a on the α was a combined effect of addition reaction, autocatalytic reaction, viscosity, and steric hindrance. From the nonisothermal curves, the curing reaction mechanism could be proposed according to the increasingly obvious low temperature peaks generated by the addition reaction of epoxy group with the primary amines in API and IPD molecules. Using the preferred resin formulation, the resin system could be cured within 10 min at 120 °C with a relatively good mechanical performance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47950.     

最优化算法与纯元素谱剥离相结合的能量色散X射线荧光谱解谱方法

在进行能量色散X射线荧光光谱(EDXRF)解谱时,如果给定样品的元素构成,采用纯元素谱图剥离的方式会更加合理,但由于每个元素的谱线都不止一条,如果仅仅针对主线对齐做剥离,会导致结果的严重失真,同时剥离次序对解谱结果有较大影响。介绍了一种最优化算法与纯元素谱剥离相结合的EDXRF解谱方法,该方法以多个纯元素谱的强度大小和峰位漂移道数作为变量构建残差方程,并用最优化计算的方法去调整,直至残差达到极小。实验采用强度顺序剥离、能量顺序剥离和最优化算法拟合3种方法分别对谱线重叠较为严重的La-Ce-Pr-Nd混合液样品的L系谱线进行了解析,结果表明最优化计算方法拟合的谱图与原始谱的残差 (1415.0)比另两种方法(166094.0和3192.7)大幅度缩小,拟合谱与原始谱更为吻合,并且方法在实现时对初值不敏感,解谱精度也不依赖于剥离次序。     

上海市火力发电行业能源计量现状分析

能源计量与节能监测、能源审计、能源统计、能源利用状况分析是用能单位能源管理和节能工作的基础。通过对本市部分火力发电企业的现场调研，针对性地提出改进建议，以期帮助用能单位增强能源计量在节能减排工作中的有效性。     

多层介质膜脉宽压缩光栅清洗方法研究

采用SPM (Sulfuric-Peroxide Mixtures, 98wt%H₂SO₄+30wt%H₂O₂)+兆声(方法1)和氧等离子体+HPM (Hydrochloric/Peroxide Mixture, 37wt%HCl+30wt%H₂O₂+DIH₂O)+兆声(方法2)两种清洗方法对多层介质膜脉宽压缩光栅进行清洗, 并对清洗前后样品的表面元素含量、衍射效率、表面粗糙度、表面温升以及激光损伤阈值等参数进行测量以评估两种清洗方法清洗效果。在入射角70°, 脉宽12 ns, s偏振, 波长1064 nm的激光辐照下, 经过清洗方法1清洗后的光栅样品单脉冲激光损伤阈值为7.55 J/cm ², 而方法2清洗后的样品损伤阈值为5.32 J/cm ²。另外, 虽然经过方法2清洗后样品表面杂质含量更低, 但是在衍射效率、表面粗糙度和表面温升都劣于经方法1清洗后的样品, 进一步分析发现方法2中氧等离子体清洗过程引入的Fe元素影响了其样品损伤性能和温升性能。因此, SPM清洗方法可以作为多层介质膜脉宽压缩光栅提升抗激光损伤性能的优化清洗方案。     

A review on coupling Green sources to Green storage (G2G): Case study on solar-hydrogen coupling

The present review paper aims to shed lights on the concept of fully green energy system which includes both the source of energy and the storage system. The objective is to propose an energy label “Green to Green” (G2G) that identifies systems involving simultaneously green source and green storage, as an efficient solution to achieve a significant reduction in the dangerous level of pollution that most countries have reached today. Green sources include mainly renewable energy systems such as solar, wind, geothermal and wave energy systems. In its turns green storage includes pumped hydroelectric, flywheel, hydrogen and compressed air. Moreover, and as a case investigation on G2G concept, the paper reviews the main solar-hydrogen coupling systems, that are categorized within four categories parabolic trough-hydrogen, solar tower-hydrogen, photovoltaic-hydrogen and solar chimney-hydrogen.     

Environmental and energy life cycle analyses of passenger vehicle systems using fossil fuel-derived hydrogen

Hydrogen energy utilization is expected due to its environmental and energy efficiencies. However, many issues remain to be solved in the social implementation of hydrogen energy through water electrolysis. This analyzes and compares the energy consumption and GHG emissions of fossil fuel-derived hydrogen and gasoline energy systems over their entire life cycle. The results demonstrate that for similar vehicle weights, the hydrogen energy system consumes 1.8 MJ/km less energy and emits 0.15 kg-CO 2 eq./km fewer GHG emissions than those of the gasoline energy system. Hydrogen derived from fossil fuels may contribute to future energy systems due to its stable energy supply and economic efficiency. Lowering the power source carbon content also improved the environmental and energy efficiencies of hydrogen energy derived from fossil fuels.     

Inductive effect in Mn-doped ZnO nanoribon arrays grown on Ni foam: A promising key for boosted capacitive and high specific energy supercapacitors

Transition metal oxides have been explored in supercapacitor applications owing to their safety, low cost, high specific capacitance and high electrochemical activity. Among all transition metal oxides, zinc oxide based materials show remarkable response for designing the supercapacitors with high electrochemical activity. Here in, Mn doped ZnO (Zn_1-xMn_xO₃ with x = 0, 0.25, 0.50, 0.75 and 1) was synthesized by a facile hydrothermal method. Doping of Mn into the ZnO increased the surface area and decease the charge transfer resistance for the Zn_0.5Mn_0.5O₃. All the synthesized materials were characterized by x-ray diffraction (XRD), scanning electron microscopy SEM), BET, electrochemical tests and other various analytical techniques to confirm the structural, morphological, textural and suprcapacitive properties. The synthesized material Zn_0.5Mn_0.5O₃ having the porous nanoribons structure with BET surface area (2490 cm²/g). The electrochemical studies showed significantly enhanced response toward pseudocapacitive nature. The synthesized material exhibited the excellent specific capacitance (515F/g), specific energy (28.61 Wh/kg) and specific power (1000 W/kg) at current density of 2 mA/g. Such impressive and superior properties make the MnZnO₃ material as promising candidate for new generation supercapacitor applications.     

WSN低功耗低时延路径式协同计算方法

针对云计算应用于无线传感器网络(Wireless Sensor Network,WSN)时延敏感型业务时存在的高传输时延问题,提出了一种WSN低功耗低时延路径式协同计算方法。该方法基于一种云雾网络架构开展研究,该架构利用汇聚节点组成雾计算层;在数据传输过程中基于雾计算层的计算能力分步骤完成任务计算,降低任务处理时延;由于汇聚节点计算能力较弱,时延降低将导致能耗增加,WSN工作寿命减短,为此提出能耗约束下的任务映射策略,并利用离散二进制粒子群优化(Binary Particle Swarm Optimization,BPSO)算法解决能耗约束下的时延优化问题。仿真结果表明,在相同的能耗约束下,对比其他算法,基于BPSO算法得出的映射方案能有效降低业务处理时延,满足时延敏感型业务的需求。